#ifndef PROSMTJOINWALLS_H
#define PROSMTJOINWALLS_H
/*
Creo Parametric TOOLKIT declarations related to SheetMetal Join Walls feature
*/
#include <ProToolkit.h>
PRO_BEGIN_C_DECLS
/* ***************************************************************************
Feature element tree :
PRO_E_FEATURE_TREE
|
|--PRO_E_FEATURE_TYPE
|
|--PRO_E_STD_FEATURE_NAME
|
|--PRO_E_SMT_WALL_JOIN_TRIM
|
|--PRO_E_SMT_WALL_JOIN_EXTEND
|
|--PRO_E_SMT_WALL_JOIN_REFS
| |
| |--PRO_E_SMT_WALL_JOIN_REFS_CMPND
| |
| |--PRO_E_SMT_WALL_JOIN_REFS_SRF
| |
| |--PRO_E_SMT_WALL_JOIN_FLIP
|
|--PRO_E_SMT_FILLETS
| |
| |--PRO_E_SMT_FILLETS_SIDE
| |
| |--PRO_E_SMT_FILLETS_VALUE
|
|--PRO_E_SMT_BEND_RELIEF
| |
| |--PRO_E_SMT_BEND_RELIEF_SIDE1
| | |
| | |--PRO_E_BEND_RELIEF_TYPE
| | |
| | |--PRO_E_BEND_RELIEF_WIDTH
| | |
| | |--PRO_E_BEND_RELIEF_DEPTH_TYPE
| | |
| | |--PRO_E_BEND_RELIEF_DEPTH
| | |
| | |--PRO_E_BEND_RELIEF_LENGTH_TYPE
| | |
| | |--PRO_E_BEND_RELIEF_LENGTH
| | |
| | |--PRO_E_BEND_RELIEF_ANGLE
| |
|--PRO_E_SMT_DEV_LEN_CALCULATION
| |
| |--PRO_E_SMT_DEV_LEN_SOURCE
| |
| |--PRO_E_SMT_DEV_LEN_Y_FACTOR
| | |
| | |--PRO_E_SMT_DEV_LEN_Y_FACTOR_TYPE
| | |
| | |--PRO_E_SMT_DEV_LEN_Y_FACTOR_VALUE
| |
| |--PRO_E_SMT_DEV_LEN_BEND_TABLE
|
==============================================================================
Element Id Element Name Data Type
==============================================================================
PRO_E_FEATURE_TYPE Feature Type PRO_VALUE_TYPE_INT
See Note 1.
PRO_E_STD_FEATURE_NAME Feature Name PRO_VALUE_TYPE_WSTRING
PRO_E_SMT_WALL_JOIN_TRIM Trim type PRO_VALUE_TYPE_INT
PRO_E_SMT_WALL_JOIN_EXTEND Extend type PRO_VALUE_TYPE_INT
PRO_E_SMT_WALL_JOIN_REFS Surfaces Array
See note 3
PRO_E_SMT_WALL_JOIN_REFS_CMPND Surface Cmpnd Compound
PRO_E_SMT_WALL_JOIN_REFS_SRF Surface PRO_ELEM_TYPE_SELECT
See note 4
PRO_E_SMT_WALL_JOIN_FLIP Flip PRO_VALUE_TYPE_INT
see note 5
PRO_E_SMT_FILLETS Fillets Compound
PRO_E_SMT_FILLETS_SIDE Radius Side PRO_VALUE_TYPE_INT
PRO_E_SMT_FILLETS_VALUE Radius Value PRO_VALUE_TYPE_DOUBLE
PRO_E_SMT_BEND_RELIEF Bend Relief Compound
PRO_E_SMT_BEND_RELIEF_SIDE1 Side 1 Relief Compound
PRO_E_BEND_RELIEF_TYPE Relief Type PRO_VALUE_TYPE_INT
PRO_E_BEND_RELIEF_WIDTH Relief Width PRO_VALUE_TYPE_DOUBLE
PRO_E_BEND_RELIEF_DEPTH_TYPE Relief Depth type PRO_VALUE_TYPE_INT
See Note 2.
PRO_E_BEND_RELIEF_DEPTH Relief Depth value PRO_VALUE_TYPE_DOUBLE
PRO_E_BEND_RELIEF_LENGTH_TYPE Relief Length type PRO_VALUE_TYPE_INT
PRO_E_BEND_RELIEF_LENGTH Relief Length value PRO_VALUE_TYPE_DOUBLE
PRO_E_BEND_RELIEF_ANGLE Relief Angle PRO_VALUE_TYPE_DOUBLE
PRO_E_SMT_DEV_LEN_CALCULATION Developed Length Compound
PRO_E_SMT_DEV_LEN_SOURCE Dev Length Source PRO_VALUE_TYPE_INT
PRO_E_SMT_DEV_LEN_Y_FACTOR Dev Length Y Factor Compound
PRO_E_SMT_DEV_LEN_Y_FACTOR_TYPE Y Factor Type PRO_VALUE_TYPE_INT
PRO_E_SMT_DEV_LEN_Y_FACTOR_VALUE Y Factor Value PRO_VALUE_TYPE_DOUBLE
PRO_E_SMT_DEV_LEN_BEND_TABLE Dev Length Bend Table PRO_VALUE_TYPE_INT
-------------------------------------------------------------------------------
Note 1.
PRO_E_FEATURE_TYPE must be of PRO_FEAT_JOIN_WALLS
-------------------------------------------------------------------------------
Note 2.
The element PRO_E_BEND_RELIEF_DEPTH_TYPE has been added in Creo Parametric.
This element rules the visibility of the bend relief depth element
PRO_E_BEND_RELIEF_DEPTH. The old element PRO_E_BEND_RELIEF_DEPTH will be used
if PRO_E_BEND_RELIEF_DEPTH_TYPE is PRO_BEND_RLF_DEPTH_BLIND or
PRO_BEND_RLF_DEPTH_TYPE_PARAM and part parameter SMT_DFLT_BEND_REL_DEPTH_TYPE
is "Blind". It is recommended to define PRO_E_BEND_RELIEF_DEPTH_TYPE explicitly
for all Creo Parametric TOOLKIT applications. Otherwise the element will be automatically
filled by the default value. The default value in Creo Parametric depends on
the part parameter SMT_DFLT_BEND_REL_DEPTH_TYPE and the configuration option
smt_drive_tools_by_parameters Yes/No. If the value of the option is No,
then the default value will be the last bend relief type, as selected
by the user in the dashboard UI during creation of a new feature.
If the default value is not "Blind", Creo Parametric TOOLKIT applications prior to this
release will not use the element PRO_E_BEND_RELIEF_DEPTH.
To fix it, set PRO_E_BEND_RELIEF_DEPTH_TYPE to PRO_BEND_RLF_DEPTH_BLIND.
Note 3.
PRO_E_SMT_WALL_JOIN_REFS - Array of exactly two elements.
Note 4.
PRO_E_SMT_WALL_JOIN_REFS_SRF - Should be plane. Should be in geometry.
There are two of them, they should not be parallel,
If they are part of the same distinct piece,
they should not be of different smt sides
Note5.
PRO_E_SMT_WALL_JOIN_FLIP - govern which part of intersected surface is removed
================================================================================
Element Id Valid Values
================================================================================
PRO_E_SMT_WALL_JOIN_TRIM ProSmtJoinWallsTrimType (See below)
PRO_E_SMT_WALL_JOIN_EXTEND ProSmtJoinWallsExtType (See below)
PRO_E_SMT_WALL_JOIN_FLIP ProBoolean
PRO_E_SMT_FILLETS_SIDE ProSmdRadType (See ProSmtFlangeWall.h)
PRO_E_BEND_RELIEF_TYPE ProBendRlfType (See ProSmtFlangeWall.h)
PRO_E_BEND_RELIEF_DEPTH_TYPE ProBendRlfDepthType (See ProSmtFlangeWall.h)
PRO_E_BEND_RELIEF_LENGTH_TYPE ProBendRlfLengthType(See ProSmtFlangeWall.h)
PRO_E_SMT_DEV_LEN_SOURCE ProDvlLenSrcType (See ProSmtFlangeWall.h)
PRO_E_SMT_DEV_LEN_Y_FACTOR_TYPE ProDvlLenFactor (See ProSmtFlangeWall.h)
PRO_E_SMT_DEV_LEN_BEND_TABLE int (bend table ID)
================================================================================
*****************************************************************************/
typedef enum Pro_intwalls_trim_type
{
PRO_INTWLS_TRIM_OPEN_CUTS = 0, /* Cut planes normal to int lines */
PRO_INTWLS_TRIM_BNDR_EXTS = 1, /* Extend int lines to plane boundaries */
PRO_INTWLS_TRIM_BEND_LINE = 2 /* Trim by bend surface */
}ProSmtJoinWallsTrimType;
typedef enum Pro_intwalls_ext_type
{
PRO_INTWLS_EXT_LINE_TO_INT = 0, /* Extend intersection line to int area */
PRO_INTWLS_EXT_LINE_TO_ALL = 1 /* Extend intersection line to all plane */
}ProSmtJoinWallsExtType;
PRO_END_C_DECLS
#endif /* PROSMTJOINWALLS_H */